|
Features and Benefits:
- Superior
abrasion-resistance and impact resistance
- Resistance to
water and weather
- Good
resistance to a wide range of chemicals including diluted acids,
alkalis and solvents
- Highest
ceramic bead concentration offered on the market; 70% concentration of
Aluma-Sand® solid ceramic beads (20-40 mesh) suspended in an epoxy
resin
- Outperforms
other coatings-more performance for investment
- Decreases
downtime and costs; increases equipment life
- Aluma-Plate
can be cast or molded, non-sagging consistency
- Easy to mix
and to use, adheres to almost any cleaned surface
- Ideal for
patching and maintenance work
|
Two kit sizes
available:
GALLON KIT:
(2) One gallon pails of ceramic bead concentration in epoxy resin and (2) 8
oz. bottles of hardener
Shipping weight: 41 lbs. (18.6 kg)
QUART KIT: (1) One
quart can of ceramic bead concentrate in epoxy resin and (1) 2 oz. bottle of
hardener
Shipping weight: to 10 lbs. (4.5 kg)
Maximum use
temperature: 200° F (93°C)
Shelf life: Up to one year; store at room temperature.
Color: Light-purple
Usage information on back. Please read thoroughly.
Steel Surface
Preparation:
Remove dirt, grease and oil with suitable industrial grade cleaner. Remove
dust and mill scale by sandblasting to a white metal finish. Follow by
vacuum cleaning or oil free dry blasting. Be sure the surface is completely
dry (and cool if sandblasted or torch cleaned) before applying Aluma-Plate.
For large areas or for overhead or vertical side wall installations, use of
welded hangers, anchor studs or tack-welded expanded metal is recommended
for support.
Mixing:
Individually
mix both the resin container (Part A) and the bottle of hardener (Part B)
thoroughly in the unlikely event that any settling has occurred. After
mixing, add entire contents of hardener bottle (Part B) to resin container
(Part A) and thoroughly mix also. Blend the two thoroughly in the container
supplied. The components are pigmented to ensure proper mixing. Mix until a
uniform light purple color is achieved. Mix completely and scrape sides and
bottom of container — be sure all “stripes” of unmixed materials from the
sides and bottom of container are thoroughly blended. DO NOT add water,
sand, Portland cement or other fillers to the epoxy matrix. When mixing, use
rubber gloves to avoid contact with skin.
Application:
Use as a patching or lining compound. Install at a nominal thickness of
1/8”-1/4” by troweling or “buttering.” Allow installation to cure, and
protect it from water and weather for a minimum of 24 hours at 70°F (21°C).
For cold weather application, heat surface to be coated so that it is
approximately 70°F.
Coverage:
One U.S.
gallon of Aluma-Plate contains material to cover 252 cubic inches (4130 cm)
or 7 square feet at 1/4" thick (0.65 square meter at 6 mm thickness)
surface.
Cure Time:
Maximum pot
life at 70°F (21°C) is 30 minutes. Initial set time is two to three hours.
Final cure is 24 hours (75%) and 100% curing achieved in seven days. Note:
The lower the ambient temperature, the longer the curing time.
Warning:
Harmful
vapor, use in good ventilation — may cause burns or allergic reactions
Avoid contact with eyes, skin or clothing
In case of contact, wash thoroughly with warm water and soap
In case of contact with eyes — flush eyes with water immediately for at
least 15 minutes and get immediate attention.
Refer to MSDS sheet for Aluma-Plate.
Disclaimer:
This
information is furnished for your investigation and independent
verification. CerCo LLC Diamonite Products shall in no event be
responsible for any damage directly or indirectly resulting from the use of
information enclosed, and makes no warranty, either expressed or implied, of
merchantability or fitness of use, or of any nature with respect to the
product or data therein.
For more information,
call CerCo LLC at (330) 567-2145. |
